Audio Visual Kart title card for a guide to the 80 Hz crossover, calling 80 Hz a sensible default, not a law, because speakers, subwoofer and the room all get a vote.

Why everyone quotes 80 Hz

Every subwoofer discussion ends up at the same two bits of advice. Set the crossover to 80 Hz. And if you want more bass, set your speakers to Large. The first one is a sensible starting point. The second is how a lot of people end up with boomy, uneven bass and a subwoofer they blame unfairly.

My position is simple: 80 Hz is a good default, not a law. The right crossover depends on what your speakers actually do at the bottom end, and on the room they are sitting in. The menu number is the least interesting part of the decision.

Even Denon is modest about it. The AVR-X2700H manual sets 80 Hz as the default and says it "will work best with the widest variety of speakers." The widest variety. Not yours specifically. That is a manufacturer telling you, politely, that it has never seen your living room.

What a crossover actually does

A crossover is a hand-off. Below the crossover frequency, the AVR takes bass away from your speakers and sends it to the subwoofer. Above it, the speakers carry on as normal. The sub does the heavy low-frequency lifting, and the speakers get to concentrate on what they are good at.

The part most people miss: the hand-off is not a cliff. The filter has a slope, so the speaker fades out gradually as the sub fades in. There is a region around the crossover point where both are playing the same notes at the same time.

That overlap is where integration succeeds or fails. Get it right and the bass sounds like it comes from the whole system. Get it wrong and you hear two separate boxes, or a hole in the middle where something should be.

Illustrative chart of the crossover as a hand off, not a cliff: the subwoofer fades out and the speakers fade in around an 80 Hz crossover point, with a shaded overlap where both play the same notes.

Small, Large and the "more bass" myth

On a Denon AVR, the Small and Large labels have nothing to do with the physical size of the speaker. According to the manual, sound below the crossover is cut from any speaker set to Small. Set a speaker to Large and the display shows "Full Band": the crossover cannot be set for it at all, and that speaker gets everything.

There is one more switch. In Subwoofer Mode "LFE", only Small speakers can have a crossover. In "LFE+Main", speakers can be set regardless of their size setting and the crossover becomes settable for them too.

The selectable values on the AVR-X2700H are 40, 60, 80, 90, 100, 110, 120, 150, 180, 200 and 250 Hz, with 80 Hz as the default. Plenty of choice, which is exactly why people fiddle.

Now the engineering reasoning, labelled as such. A small bookshelf speaker that is relieved of deep bass can usually play cleaner and louder, because it is no longer straining to reproduce notes it was never built for. Set that same speaker to Large "so it has more bass" and it simply works harder, and its output can fight the sub's in the room. The result is often boomy or uneven bass, not more of it.

Calling a speaker Large does not make it large. It just takes away its safety net.

Floorstanders are a fairer case. Some can be left on Large. Even so, in many rooms they still sound better set to Small with the sub taking the load.

The crossover steps on a Denon AVR, 40, 60, 80, 90, 100, 110, 120, 150, 180, 200 and 250 Hz, with 80 Hz marked as the default, and a note that Small cuts sound below the crossover while Large shows Full Band.

Why the room gets a bigger vote than the number

Here is a calculation, not a measurement. With sound travelling at about 343 m/s at roughly 20 C, the wavelength at 40 Hz is about 8.6 m. At 80 Hz it is about 4.3 m. At 120 Hz, about 2.9 m. At 200 Hz, about 1.7 m.

Waves that long are on the same scale as the room itself. At these frequencies the room's dimensions shape what you hear more than the speaker does. The bass reflects off walls, floor and ceiling and piles up or cancels depending on where you sit.

There is a second consequence. As you push the crossover higher, the sub starts reproducing sounds with more directional cues in them, so it becomes easier to tell where the sub is sitting. That is the general engineering reasoning for not running the crossover higher than your speakers need.

This is why the sub's position and the room matter more than the exact crossover number. A low crossover with a badly placed sub does not fix anything. It just moves the problem. Your AVR cannot change the laws of acoustics because the setup menu asked nicely.

Indian homes make this sharper. Marble or tile floors, large glass windows and untreated open-plan living rooms reflect bass freely. And in an apartment, the shared wall decides how much of your bass reaches the neighbours before it reaches you.

Bar chart of bass wavelength in metres: about 8.6 m at 40 Hz, 4.3 m at 80 Hz, 2.9 m at 120 Hz and 1.7 m at 200 Hz, the same scale as a living room.

The double filter trap, and a word on phase

Most subwoofers have their own crossover knob. If you leave it set low and also run the AVR's crossover, you have two filters stacked on the same signal. Two filters doing one job is not teamwork. It is a committee.

Denon's Audyssey setup page says that if your subwoofer has a direct mode, you should switch it On. That disables the sub's own volume adjustment and crossover setting, so the AVR does the filtering. For a sub without direct mode, the same page says to set its crossover to the highest frequency, so it gets out of the way.

Then there is phase and level at the hand-off. In the overlap region, speaker and sub are playing the same frequencies. If their output arrives out of step, they can partly cancel and leave a dip. If the sub level is set too high, the hand-off turns into a hump. I will not give you a magic number for either, because there isn't one: it depends on the distances, the placement and the room. It has to be measured or carefully listened for, not guessed.

Audyssey is a starting point, not gospel

Automatic setup gets you most of the way, and you should run it. But read the results with some care.

Denon's own Audyssey page notes that subwoofers may measure a greater reported distance than the actual distance. So a number that differs from your tape measure is not automatically an error. Treat it as one reading, and check it against the room.

Denon also says not to change the speaker connection or subwoofer volume after Audyssey Setup. If you do, run Audyssey Setup again so the equaliser settings match the system you actually have. Turning the sub knob up afterwards "because it felt light" quietly undoes the calibration you just ran.

Practical rules for three kinds of speakers

These are starting points from experience, not measurements. The room still gets a vote.

  • Bookshelf speakers: set them Small and start at 80 Hz. If the hand-off sounds thin or lumpy, try the next step or two up in the menu. Do not set them Large to chase bass.
  • Small floorstanders: Small at 80 Hz is the safe default. Going lower is acceptable only if the speaker's real low end in your room supports it, which you find out by listening or measuring, not from the box.
  • Big floorstanders: Large, or LFE+Main, can work. In many rooms Small with the sub taking the load still sounds tighter. Try both and keep whichever is more even across seats, not whichever is louder.
  • When the rule stops mattering: if the sub is in a bad spot, no crossover setting will rescue it. Fix placement first, then return to the number.

"But my speakers go down to X Hz, so why use a crossover?"

Fair question. On paper, if a speaker reaches low enough, why not let it play everything?

Because a spec sheet figure is a manufacturer claim. It tells you what the speaker can do, not how that bass will behave in your room. Your main speakers are placed for imaging and dialogue. Your sub can be placed for bass. Those are usually different spots, and the room treats them differently.

Letting the speakers play full range also means they work harder and can overlap with the sub in ways that make the bass less even, not more. The exception would be large, capable floorstanders in a room that behaves well. Even then, I would compare both settings rather than assume.

What this means before you buy anything

Do not buy anything yet. Most bass complaints we hear are settings and placement, not hardware. Check that your speakers are set to Small, that the crossover starts at 80 Hz, that the sub's own crossover is in direct mode or turned to maximum, and that you reran Audyssey after any change. Then try moving the sub.

If the bass is still uneven after all that, it is worth talking about the room, a second sub or a different speaker. Usually in that order.

If you want a second opinion, share your room size and speaker models with us on WhatsApp at +91 88820 19272 for a free consultation. And if you would rather have the hand-off measured and set properly, calibration is a paid service we offer. No rush. The bass will still be there when you are ready.

Leave a comment

All comments are moderated before being published

Join Our WhatsApp Channel

  • Exclusive AV deals
  • Pro tips for your home theater & stereo setup
  • Industry news & honest insights
  • Setup advice straight from the experts
    Click Here!