Five receivers, and one question that quietly decides most of them: what happens when you outgrow this box?
That is the real argument with a 7.2 receiver, and almost no buying list goes near it. Watt numbers get compared. HDMI versions get compared. The one connector that determines whether you can keep the receiver and add an external power amplifier in three years gets a tick in a table, if it appears at all.
So let me put the position before the list rather than after it. In this price band, the pre-out row matters more than the power rating. Of the five receivers below, exactly two let you keep the processing and replace the amplification later. The other three do not, and that is perfectly acceptable, as long as you know it before you buy rather than eighteen months afterwards.
This list is shorter than it used to be, deliberately. Every model here is one we currently supply as an authorised dealer, at a live listed price, in a range we are willing to stand behind for service. Models we no longer put in front of buyers have been removed rather than left in to pad the count. A shorter list you can trust beats a longer one you cannot.
Why 7.2, and when it is the wrong shape entirely
A 7.2 receiver gives you seven amplified channels and two subwoofer outputs. In practice, almost nobody in an Indian living room runs seven speakers in a flat circle. They run five, and put the remaining two amplifier channels into height.
That is why 5.1.2 is far and away the most common configuration in the systems we quote. Not 7.1. Not 7.2.4. A five-channel bed, one or two subwoofers, and two ceiling speakers. The 7.2 receiver is popular because it is the cheapest way to reach that layout with a channel in hand.
Which leads to the first thing worth checking. Most 7.2 receivers cannot drive seven speakers and two height channels at once. They allocate. Read the manufacturer's own maximum configuration line, because 7.2 on the front of the box usually means 5.2.2 in the setup menu.
If your room is a 3.5 to 4.5 metre seating distance in an open plan hall, which describes a large share of what we install, the useful question is not seven channels or nine. It is whether the ceiling can take two height speakers. In the systems we build, height channels go into the ceiling rather than into up-firing modules by a very wide margin, because a hard ceiling reflects predictably and an up-firing driver aimed at a fan does not.
The pre-out row, and why it decides more than the power rating
A pre-out is a line level output carrying the signal for one channel before it reaches the receiver's internal amplifier. If a receiver has a full set, you can feed those outputs into an external power amplifier and the receiver becomes a processor. Your investment in decoding, room correction, HDMI switching and setup survives the upgrade.
If it has only subwoofer pre-outs, the only thing you can add externally is a subwoofer. The day your speakers need more current than the receiver can deliver, you replace the whole unit.
This is not a subtle distinction in a country where a serious speaker package often arrives before a serious amplifier. Around one in eight of the systems we quote includes a separate power amplifier, and that decision is usually made a year or two after the receiver was bought, by which point the pre-out question has already been answered permanently.
A pre-out costs a manufacturer very little to include. Its absence costs you an entire receiver.
Here is what the manufacturers' own specification tables say for the five below. Two have full 7.2 pre-outs: the Marantz Cinema 70s and the Marantz Cinema 60, both listed by Marantz as "Multichannel Preamp Out 7.2". The Denon AVR-X2900H offers a partial set, listed as "Yes (2.2)", meaning front left and right plus two subwoofers. The remaining two are subwoofer only.
I am naming that as a specification claim, not as a measurement. It is one of the few things on a receiver spec sheet that is simply true or false, which is precisely why it is worth checking before the softer numbers.
An honest note about where these numbers come from
While putting this together I found that Denon's own documents disagree with each other about the AVR-X1800H. One North American info sheet lists "Multichannel Pre-Out Yes (2.2)". The global and US specification tables have no such row at all and list only two subwoofer outputs. The owner's manual, describing the rear panel, says the PRE OUT connectors are "used to connect a subwoofer with a built-in amplifier".
Three official sources, two answers. When a manufacturer's own PDF disagrees with its own manual, the safe assumption is not the flattering one. I have treated the X1800H as subwoofer pre-outs only, and I would rather tell you the documents conflict than pick the version that makes the receiver sound better.
The same range has smaller contradictions elsewhere. Denon's global page lists the X1800H's room correction as MultEQ XT in one section and MultEQ in another; the manual has a dedicated MultEQ XT page, so XT is what I have used. Marantz's Cinema 60 page says MultEQ XT in the specification table and MultEQ in the comparison block directly above it, and the new Series 2 page repeats the identical contradiction. These are not conspiracies, they are content management systems. But they are a good reason to distrust any list that quotes a spec without saying where it came from.
Power ratings: what the number is actually measuring
Every 8 ohm figure quoted below is the manufacturer's rating with two channels driven across the full 20 Hz to 20 kHz band at a stated distortion figure. That is the honest version of the measurement. It is also not the condition your system runs in, because a film soundtrack asks five to seven channels for current at the same moment.
The number on the box is measured with two channels playing. Your Atmos mix did not agree to that condition.
It is also why you should read the small print under any larger figure a receiver advertises. The same amplifier can be quoted twice: once at 8 ohms, across the full audio band, with two channels driven, at a fraction of a percent distortion, and once at 6 ohms, at 1 kHz only, with a single channel driven, at ten percent distortion. Both numbers are real measurements taken from the same box. Only the first one describes your living room, and it is always the smaller one. When a spec sheet gives you the big number without the conditions, the conditions were the interesting part.
This is not a hypothetical. It is the single most common way a receiver is made to look bigger than it is, and you will meet it on the newest models as readily as the oldest. Denon's own specification table for the incoming AVC-X2850H quotes the same amplifier four ways, from 95 watts to 185 watts. Only the 95 watt figure is measured under conditions that resemble your room.
If you want the longer version of this argument, we wrote it out separately in AV receiver power ratings and what watts per channel really mean, and the amplifier class question is covered in our piece on Class A, AB and D.
The practical rule: with a sensitive speaker of around 92 dB or higher, at a 4 metre seat, in a normal living room, the difference between 80 and 100 watts is not what you will hear first. Speaker sensitivity and room treatment move the result far more than twenty watts on a spec sheet. Below roughly 87 dB sensitivity, or with a difficult 4 ohm load, the amplifier starts to matter.
Room correction, and what it cannot do
Three tiers appear on this list. Audyssey MultEQ is the base version. MultEQ XT uses more filter resolution. Dirac Live is a different system entirely, sold as a paid licence on the models that support it.
All of them measure your room from a microphone and apply correction. All of them are better at fixing dips and peaks below a few hundred hertz than at fixing a hard reflective surface. Room correction is very good at fixing what it can measure from where you put the microphone. It has no opinion about the marble.
That distinction earns its keep in Indian rooms. Vitrified tile or marble floors, large glass, and minimal soft furnishing produce early reflections and a long decay in the upper midrange. Correction software can flatten the frequency response at the seat. It cannot shorten the decay. That is what a rug, curtains and some absorption at the first reflection points are for, and it is the single cheapest improvement available to most of the rooms we see.
So: buy the receiver for the connections and the amplifier, not for the correction tier. Then treat the room. Then calibrate. Our professional installation and calibration service runs at three levels depending on how far you want to take it, and the fair answer for a lot of rooms is that the first level plus a rug does most of the work.
Generation status, so you know what you are buying
This is the section most buying lists leave out, and it is the one that costs people money. Three of the five below have a newer version in existence somewhere in the world, and you should hear that from us rather than from a forum three weeks after delivery.
We have opened a page for each incoming model so you can register interest and be told when stock lands. None of the three carries a price, because no India price has been announced and we will not invent one.
Marantz. Marantz announced the CINEMA Series 2 range on 6 August 2026, which includes a CINEMA 60 Series 2 and a CINEMA 70s Series 2. Per Marantz's own announcement, the Series 2 models bring a new 32-bit eight-channel DAC, Web Control 2.0 for configuration without television menus, 1440p video pass through with AMD FreeSync compatibility, and Dirac Live upgradeability extended to the 60 and the 70s for the first time. Global availability was stated as 12 August 2026, with the 70s Series 2 from 15 September 2026. Our distributor has indicated Indian availability from October.
Denon. Denon has announced the AVC-X2850H, listed on its own global site as a 7.2 channel, 95 watt, 8K model, as the successor to the X2800H. It keeps Audyssey MultEQ XT, adds a moving magnet phono input, and its pre-out row is two channel plus two subwoofer outputs rather than a full set. Denon still shows it as not yet shipping.
The AVR-X2800H has been withdrawn from our range and is no longer listed. It remains a good receiver and anyone who owns one should keep enjoying it. We simply will not sell a model whose replacement has been announced and whose supply we cannot stand behind.
The AVR-X2900H is the current Denon generation on this list, and the X1800H continues in Denon's lineup. The S980H sits slightly apart, a newer chassis with an older correction tier, which is explained in its entry below.
Here is the honest way to use all that. If Dirac Live on a slim or mid-priced Marantz is the reason you were shopping, wait for the Series 2, because Marantz lists Dirac Live as not supported on both current models below. If what you want is full pre-outs, Marantz's amplifier tuning and a receiver you will keep for a decade, the current models do that today, and a newer converter does not change the connector count on the back panel. A new generation does not make the previous one worse. It does change what the previous one ought to cost, which is worth a conversation before you order.
The five, in price order
Every model here is one we currently stock as an authorised dealer, with warranty as per brand and distributor policy. Prices are our current listed India prices including GST, and they move, so the product link is the authority rather than this paragraph. Where a maximum retail price exists it is shown alongside.
1. Denon AVR-X1800H, 55,400 rupees (MRP 1,19,900 rupees)
Denon rates it at 80 watts per channel into 8 ohms, 20 Hz to 20 kHz, 0.08 percent distortion, two channels driven. Six HDMI inputs with three supporting 8K, one output with eARC, and the full gaming set of 4K at 120 Hz, VRR, ALLM and QFT. Audyssey MultEQ XT. Maximum layout is 7.2 or 5.2.2.
This is the value anchor of the list and the one I recommend most often to someone building their first proper system. The limit is the one discussed above: subwoofer pre-outs only, and a single HDMI output. If a projector and a television both need feeding, this is the wrong receiver.
2. Denon AVR-S980H, 77,450 rupees (MRP 1,54,900 rupees)
Ninety watts into 8 ohms, two channels driven, 0.08 percent. Six HDMI in with three at 8K, two out. VRR, ALLM and QFT. Denon's own info sheet describes expanding to a 7.1 or 5.1.2 layout.
The second HDMI output is the real reason to step up from the X1800H, not the ten watts. If you have a projector and a TV in the same room, this is where the list starts working for you. The catch is the correction tier: this is plain Audyssey MultEQ, not XT, despite sitting well above the X1800H on price. You are paying for a newer chassis and a second output rather than a better calibration engine. Not worth it if MultEQ XT was the reason you were shopping.
3. Denon AVR-X2900H, 97,450 rupees (MRP 1,94,900 rupees)
Ninety five watts into 8 ohms, MultEQ XT, and the one properly interesting feature in the middle of this list: Denon lists it as ready for a Dirac Live Room Correction upgrade, sold separately as a licence. Its multichannel pre-out is listed as "Yes (2.2)", front left and right plus two subwoofers.
Those partial pre-outs are more useful than they look. Front left and right are the channels that run out of headroom first in a large room, so a stereo power amplifier on the fronts is the most common first upgrade anyone actually makes. If you already know an external amplifier is coming, this is the cheapest receiver here that lets you do it properly. We compared this generation against the previous one in our 2026 upgrade piece. It is also the model an EISA jury picked as its AV Receiver of the year, which is mild supporting evidence and not a reason on its own.
4. Marantz Cinema 70s, 1,46,600 rupees (MRP 1,90,900 rupees)
Fifty watts into 8 ohms, 20 Hz to 20 kHz, 0.08 percent, two channels driven. Class A/B discrete amplification. Full 7.2 multichannel pre-outs, listed by Marantz as "Multichannel Preamp Out 7.2". Audyssey MultEQ, base tier. Dirac Live is listed as not supported. Six HDMI in with three at 8K, one output. The chassis is 109 mm tall and weighs 8.7 kg.
Read those two facts together, because they define the receiver. Fifty watts is the lowest power on this list. Full pre-outs are the most flexible connection on this list. This is not a powerhouse, it is a slim processor with a modest amplifier attached, aimed at a cabinet that will not take a full size receiver.
My view: with efficient speakers in a small to medium room it is more than enough, and if you later add a power amplifier it becomes the longest lived purchase here. With 87 dB bookshelf speakers in a large open hall, fifty watts will run out before you want it to. Buy it for the shape of your cabinet and your upgrade path, not for the wattage. See the generation note above before you order.
5. Marantz Cinema 60, 2,31,900 rupees
One hundred watts into 8 ohms, 20 Hz to 20 kHz, 0.08 percent, two channels driven, and 140 watts into 6 ohms at 1 kHz. Class A/B discrete amplification with Marantz's HDAM circuitry and current feedback topology. Full 7.2 multichannel pre-outs. Six HDMI in with three at 8K, two out with eARC. A moving magnet phono input, which nothing else on this list offers. Audyssey MultEQ XT per the specification table. Dirac Live is listed as not supported.
This is the most complete receiver on the list and the one I would buy if I were keeping it for a decade. Full pre-outs, real power, a phono stage, and a chassis at 10.9 kg that is built like it expects to be driven. Marantz quotes 650 watts of power consumption, which is worth remembering before it goes into a closed cabinet. A receiver in a sealed cupboard will find a way to tell you.
The counterargument is simple arithmetic: it costs roughly four times the X1800H and delivers twenty watts more. You are paying for the pre-outs, the build and the tonal character, not for output.
One more thing worth saying plainly, because it concerns our own price list rather than a manufacturer's. At the time of writing, our listing for the nine channel Marantz Cinema 50 sits a little below the Cinema 60 on this page. If you are at this budget and your room could use two more amplified channels, ask us about the Cinema 50 before you order. If seven channels is all you need, the Cinema 60 is still the right box. I would rather you saw both numbers than found out later.
What I would tell you if you asked me directly
If you are building a 5.1.2 system in a normal Indian living room with reasonably sensitive speakers and one display, the Denon AVR-X1800H does almost everything you need and leaves budget for a better centre speaker, which will do more for dialogue clarity than any receiver upgrade. Centre channel matching is covered properly in our piece on timbre matching. Add a projector alongside the television and you need a second HDMI output, which moves you to the S980H or the X2900H.
If you want the current Denon generation, MultEQ XT and a Dirac Live upgrade path in one box, the X2900H is the one I would point you at, and it is the cheapest receiver here with pre-outs on the front channels.
If you already know that a power amplifier is coming, stop comparing wattage and buy pre-outs. That means the Cinema 70s, the Cinema 60, or the X2900H with its front channel pre-outs.
If you drive your system hard, in a large room, with demanding speakers, the Cinema 60 is the one on this list designed for it, and at that point the conversation is really about whether a separate power amplifier belongs in the budget from day one.
And if you already own a working receiver from the last five or six generations: you may not need any of this. A real room measurement, some absorption at the first reflection points, a correct crossover setting and a proper calibration will beat a new receiver in most rooms, for less money. Keeping what you own and fixing the room is a perfectly good conclusion, and we would rather you reached it here than after a return request.
Practical things that catch people out in India
- Ventilation. These receivers run warm, and the Cinema 60 draws up to 650 watts by Marantz's own figure. A closed cabinet without airflow shortens the life of the unit and triggers thermal protection during long films.
- Mains voltage. Fluctuating supply is a real risk to any device with a large power supply. A stabiliser or a decent line conditioner is cheap insurance next to the cost of these units.
- Humidity. In coastal and monsoon-heavy cities, a receiver left unpowered for weeks in a damp room is more vulnerable than one used regularly. Ventilate the cabinet.
- Warranty and grey imports. Warranty on all of these is as per brand and distributor policy, and it applies to units supplied through authorised distribution. An imported unit bought cheaper elsewhere is usually not covered here, and service on a modern receiver is not a local repair job.
- Check the maximum layout, not the badge. Most of these are 5.2.2 machines when height channels are in use, whatever the 7.2 on the front says.
- Ask which generation you are being sent. Where a Series 2 or a newer suffix exists, the model code on the invoice is the only thing that settles it. A seller still clearing a superseded model has every reason not to raise the subject. Reading an invoice is free.
- Be careful with foreign prices. A dollar or euro figure for an incoming model does not convert into an Indian MRP. The gap is usually large, and it is not a currency conversion.
Where to go from here
The full range we stock is in the 7.2 channel AV receiver collection, with current prices and stock status, which is more reliable than any article.
If you would rather not work it out alone, our free room consultation exists for exactly this. It helps if you bring the room dimensions, your seating distance, the speakers you already own or are considering, and a budget band. Those four things answer most of the questions above in about ten minutes. If a model on its way to India suits you better than one on this page, we would rather tell you to wait.
And if you own a Denon or Marantz already, the more useful spend is often calibration rather than replacement. That is a paid service at three levels, and we will tell you if your room does not need the top one.
Updated 20 September 2026: the Denon AVR-X2800H has been removed and the list is now five receivers. It has been withdrawn from our range because Denon has announced the AVC-X2850H as its successor, and we will not sell a model whose supply we cannot stand behind. The closing recommendation, which previously named the X2800H, now names the X1800H for single display systems and the X2900H for the current generation. The generation status section has been expanded to cover the AVC-X2850H and the Marantz CINEMA Series 2, and each of those three incoming models now has a registration page on this site. None of the three carries a price, because no India price has been announced. Previously updated 9 September 2026: the list was cut from ten receivers to six. Previously updated 2 September 2026: rewritten from the 2025 version, with every specification re-sourced from the manufacturers' own pages and manuals, the conflicts in those documents described rather than smoothed over, and the estimated 6 ohm and 4 ohm power figures from the old comparison tables dropped entirely, because they were calculated from the 8 ohm ratings rather than measured.
