How to Connect a Home Theatre to Your TV: HDMI ARC, Optical, AUX and the Set Top Box
If your TV and your home theatre both have an HDMI port marked ARC or eARC, use it: one cable and a few settings. Optical is the backup, AUX the last resort. Here is what each connection carries, where Samsung, LG and Sony hide the settings, and where the Jio set top box should plug in.
Most people who ask us how to connect a home theatre to a TV have already plugged something in. Sound comes out of the TV speakers, or out of nothing at all, and the new system sits there with its display glowing politely. The short answer: if your TV and your system both have an HDMI port marked ARC (or eARC), use that. One cable, two or three settings, done. Optical is the backup. AUX is the last resort.
In our experience the problem is rarely a faulty box. It is a wrong port, or one setting left off on one side. The TV does not know your home theatre exists until somebody tells it.
First, which kind of system do you have?
It changes where things plug in, so settle this before touching a cable.
- An AV receiver system: a receiver (Denon, Marantz and the like) driving separate passive speakers and a subwoofer. The receiver has several HDMI inputs, one HDMI output to the TV, and does the decoding and switching.
- An all-in-one system: a soundbar, or a packaged home theatre where the main unit and speakers come in one box. These usually have HDMI ARC and optical, sometimes an HDMI input or two, sometimes none.
Both connect to the TV in the same basic way. The difference shows up later, when you decide where the set top box goes.
The four connections, best to worst
HDMI eARC, HDMI ARC, optical and AUX all get sound from the TV to the system. They do not all carry the same sound. Here is what each one can deliver, according to the format table Sony publishes for its own receivers and Samsung's ARC format list.
Look at the ARC row again. Dolby says broadcast and streaming services deliver Dolby Atmos using Dolby Digital Plus, and that most recent TVs support Dolby Digital Plus over ARC. So for a typical Netflix or Prime Video household, ARC is not a downgrade worth losing sleep over. eARC earns its keep when you play lossless tracks (a 4K Blu-ray, or an app on the TV that sends TrueHD or multichannel PCM). If you want the longer version, we have a separate answer on what HDMI eARC is and whether you need it.
HDMI ARC or eARC, step by step
This is the connection I would use in almost every room. The steps are the same on every brand; only the menu names change.
- Find the right port on the TV. It is labelled ARC, or eARC/ARC. LG warns that other HDMI ports may not return TV audio at all, and on a Samsung One Connect box the ARC port is usually the third HDMI port. Plugging into HDMI 2 when ARC lives on HDMI 3 is the most common reason "ARC does not work".
- Use a proper cable. Samsung asks for HDMI 1.4 or higher for ARC and an eARC-capable cable (marked HEAC or HEC) for eARC. Sony recommends an HDMI cable with Ethernet for the eARC link. A random cable from the drawer sometimes passes ARC and then refuses eARC, which makes for a very confusing hour.
- Connect the other end to the system's ARC port. On a receiver that is the HDMI output that goes to the TV (Denon calls it HDMI MONITOR). On a soundbar or all-in-one it is usually labelled HDMI OUT (TV-ARC).
- Switch on HDMI-CEC on the TV. This is the control link that ARC depends on. Samsung says Anynet+ (its name for CEC) must be on to use eARC, and LG says the same about SIMPLINK for ARC and eARC.
- Tell the TV to send sound out. Set the TV's sound output to the receiver or audio system rather than the TV speakers.
- Switch on ARC on the receiver. On the Denon AVR-X580BT and AVR-X1800H, both HDMI Control and ARC are Off by default, according to Denon's own manuals. This one catches a lot of people. Denon also notes that an eARC TV plays through the receiver regardless of the ARC setting, and that you should restart the connected devices after changing these settings.
- Check the digital audio output format. On Samsung this is called Digital Output Audio Format, with PCM, Auto and Pass-Through as the choices. Samsung lists PCM over ARC as two channel, so if you want surround from the TV's apps, choose Auto or Pass-Through. If the sound breaks up, Samsung's own advice is to try each of the three in turn.
Then play something with a known surround track and look at the receiver's display. If it says Dolby Digital, Dolby Digital Plus or Atmos, you are done. If it says PCM 2.0, go back to step 7.
Samsung, LG and Sony menus: same function, different names
Every TV brand names HDMI-CEC differently. Samsung calls it Anynet+, LG calls it SIMPLINK, Sony calls it BRAVIA Sync. It is the same function under three marketing departments. Here is where the settings sit, taken from each brand's support pages. Menu paths shift between model years, so treat these as the place to start looking, not gospel.
Other TV brands have the same switches under their own names. If you cannot find CEC by name, look for ARC or HDMI device control in the TV's connection or sound menu. One warning from our side: CEC is a loosely enforced standard, and it can make devices switch each other on at odd moments. If that starts happening, our note on why the TV keeps switching the receiver on explains how to tame it without losing ARC.
Optical, when HDMI ARC is not an option
Older TVs, older home theatre systems, or a system whose HDMI port is already busy: optical is the dependable fallback.
- Run an optical cable from the TV's digital audio out (optical) to the system's optical input. Pull the little plastic caps off both ends first. Light does not travel well through plastic packaging, and we have seen more than one "faulty" cable that was still wearing its cap.
- Turn on the TV's optical output. On a recent Sony BRAVIA it is under Settings > Display & Sound > Audio output > Optical digital audio output settings.
- Select the optical input on the receiver or system (on many receivers it is the TV Audio or Optical input).
The limits are worth knowing before you settle for it. Optical carries Dolby Digital and DTS, not Dolby Digital Plus or Atmos, and there is no CEC, so the TV remote will not control the system's volume. Two remotes on the sofa. What reaches the system also depends on what the TV converts an app's audio into before it leaves the optical port, which varies by TV.
AUX, the last resort
If the TV has only a headphone or analogue audio out (3.5 mm or a red and white RCA pair), you can run that into an analogue input on the system. It works. It is also two channels of analogue sound, so any surround you hear is the system upmixing stereo, not real 5.1. For a TV with no HDMI ARC and no optical, it is the only route. For anything else, it is the wrong one.
The Jio set top box, smart TV apps, and where everything plugs in
This is the part that actually decides how good the system sounds, and it is where most "connected but no surround" complaints come from. There are two sensible ways to wire a set top box, a streaming stick and a home theatre.
Route A is what most homes end up with: the Jio box (or any DTH box, Fire TV stick, Apple TV) goes into the TV, and the TV sends sound to the system over ARC or eARC. It is simple. The catch is that the TV now sits in the middle, deciding what the system hears.
Route B puts the box into one of the receiver's HDMI inputs and runs the receiver's HDMI output to the TV's ARC port. The receiver receives whatever the box sends, with nothing in between making decisions on your behalf, and the same cable still returns the TV's own apps over ARC. If you have an AV receiver, this is the route I would use. LG describes the same idea for soundbars that have HDMI inputs: set top box into the soundbar's HDMI IN, and keep the ARC link to the TV.
Two things to check on the Jio box itself. First, look at the back panel: some boxes have only an HDMI output, so HDMI is the only audio path. Second, look in the box's own settings for an audio output option (stereo, surround, auto, or similar). Jio does not publish a detailed spec sheet that we could cite, so we will not promise what a given box outputs on a given channel or app; play something, and read the format on the receiver's display. That display does not lie, which is more than can be said for some menus.
One more tip from Samsung's own troubleshooting: if ARC keeps dropping, disconnect the set top box and other external devices and test again, because some devices do not fully follow the HDMI specification.
AV receiver or all-in-one: what changes for the TV connection
For the TV link itself, not much. Both use ARC, eARC or optical. The differences are in everything around it.
A receiver gives you several HDMI inputs, so Route B is available, and it decodes whatever the sources send. The Denon AVR-X1800H lists eARC in Denon's specifications, so lossless formats from the TV's own apps arrive intact on an eARC TV. The Denon AVR-X580BT has the same ARC settings in its manual, at a lower tier. If you are choosing between them, the TV connection is not the deciding factor; room size, speaker count and Atmos plans are. Our Denon AVR-X1800H page and the AV receiver range have the details.
An all-in-one usually gives you ARC and optical, maybe one HDMI input, sometimes none. That is fine for many rooms. Without an HDMI input, you are on Route A, and the TV's audio settings matter more. If you are still deciding which kind of system to buy, our answer on soundbar versus a proper 5.1 system covers that decision.
And if your current system already plays surround properly over ARC, you do not need to buy anything. A new cable will not improve a working digital link.
Still not working? The short checklist
- Is the cable in the TV port marked ARC or eARC, not just any HDMI port?
- Is CEC on at the TV (Anynet+, SIMPLINK, BRAVIA Sync) and HDMI Control on at the receiver?
- Is ARC switched on at the receiver? On Denon it ships Off.
- Is the TV's sound output set to the receiver or audio system, not the TV speakers?
- Is the digital output format on Auto or Pass-Through, not PCM?
- Have you switched everything off and on again after changing settings? Denon asks for exactly that.
- Does surround work from one app but not another? See why some TV apps give surround and others only stereo.
- Sound arriving after the lips move? Our note on fixing lip-sync delay covers it.
- Picture blinking after you put the receiver in the chain? That is an HDMI handshake issue: here is how to sort it.
Send us your TV model and system, we will tell you the settings
Menu names change every model year, and the one setting that is wrong is never the one you would guess. If you would rather not hunt for it, send us your TV model and your system (receiver model, or the all-in-one model) on WhatsApp, along with what you have plugged where. We will tell you the right cable, the right port and the exact settings for that pair. No purchase needed for that answer.
Got a question this didn't answer?
Ask us about your own room.
Guides cover the general case. If you want an answer for your room, your budget and your gear, ask — we answer real questions publicly.
Ask AV Kart


